Are GAF Woodland shingles discontinued?

Due to limited demand and in order to ensure operational efficiency, GAF is discontinuing all colors of Glenwood® Designer Shingles as well as Woodland® Designer Shingles in the colors Tuscan Sunset and Woodberry Brown. These products will not be run again in the future.

Should shingles be glued to drip edge?

Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle. If necessary, secure the ends of the drip edge with short roofing nails; just be sure they’re positioned high up under the shingles.

Where do you nail GAF shingles?

These shingles MUST be nailed a nominal 6″ (152mm) from bottom of shingle, above the cut-outs, as shown. Nails must not be exposed.

Are GAF shingles as good as Certainteed?

Many roofers see Certainteed shingles as higher quality than GAF shingles. Some consider GAF looking cheap, but in actuality, the quality is not that different. GAF is lower-cost than Certainteed, but Certainteed shingles come in a wider variety of colors and many prefer the aesthetics of the Certainteed’s shingles.

Which shingles are better GAF or Certainteed?

Weight per square Despite having very similar dimensions, CertainTeed shingles weigh anywhere from 10% to 25% more than GAF shingles per square, though CertainTeed shingles are actually about ¾ of an inch shorter in width. In general, heavier shingles are thought to be more robust and therefore, more durable.

Does GAF require drip edge?

GAF requires non-corroding metal drip edges at the eaves where a Silver Pledge® or Golden Pledge® Limited Warranty is sought. As a matter of good roofing practice, however, GAF strongly recommends that drip edges be installed at the rakes and eaves on all GAF shingle roofs.

Do you need to remove the plastic strip on shingles?

Because the cellophane strips have no effect on the performance of asphalt shingles, it’s fine to leave them in place as you install the shingles. In fact, the effort to remove them is unnecessary and just adds an extra step for the contractor.

What to use to hold down shingles?

Any good quality brand of asphalt plastic cement will work, and can be applied from a can or caulking tube. Never apply more than a small spot of adhesive, as excess solvents in the cement may soften the shingle coating, resulting in the formation of blisters.

How to install GAF Timberline roof shingles?

Lay tarps on the ground to catch debris coming off the roof. Begin by removing shingles using a roofing fork/shovel.

  • Remove metal flashing if needed.
  • Sweep the roof deck clean to remove leftover nails and debris.

    • How to re roof with asphalt shingles GAF?

    Water inside your home (tarp your roof,then call your insurance company)

  • Clogs or damage to gutters and downspouts
  • Streaked or stained shingle
  • Water stains,bubbled paint or wetness on interior walls and ceilings
  • Light showing through the attic roof
  • Missing,cracked,torn,or bald shingles

    • How to make GAF ridge cap shingles?

    Ridge cap shingles have one nail per ridge face except the last, which has 2 per side. Nails are 5” to 6” in from the tab edge or end that will be exposed and an inch up from the widest part or edge of the tab cutout centerline. The distance depends on the amount of shingle left exposed. The nailing area usually has a dab of black asphalt

    How to install GAF mineral guard roll roofing?

    Roof Slope: 2/12 or more.

  • Roll roofing condition: The roll roofing should be clean and dry when it’s installed.
  • Roofing deck: should be clean,dry,and free of voids.
  • Roofing underlayment: install the manufacturer’s recommended underlayment on the roof deck before bringing up and installing the roof covering itself.