How do you program a Uniden Bearcat police scanner?

Programming a Handheld Model of the Uniden Bearcat Scanner Press the “Scan” button to put the handheld into scanning mode and press “Manual” to enter manual programming mode. Your scanner will have a number of available channels that can be programmed. Enter the channel number you wish to use and press “Manual” again.

How do you reset a Bearcat scanner?

Press the “2,” “9” and “Hold” keys. Continue to hold them while pressing the “Power” button for at least three seconds, until the display reads “Clear.” The Uniden NASCAR scanner is now reset and all data that was previously programmed has been erased.

How do you program a Uniden Bearcat bc700a scanner?

Member

  1. Press Search.
  2. Press Band to locate the frequency band.
  3. Press Hold when you get close to the frequency you want. Then using the Up or Down key locate the exact frequency.
  4. Press Program.
  5. Press Private.
  6. To locate the channel you want press the Up or Down key.
  7. Once you locate the channel, press program.

How do you reset a Uniden Bearcat BC350A?

Reset Uniden Scanner

  1. Turn the scanner OFF and unplug the audio cable from the rear of the scanner.
  2. Press and hold the L/O and PROG buttons.
  3. While holding L/O and PROG, turn the scanner on.
  4. Release the L/O and PROG buttons.
  5. Press the PD/FD/EMG button THREE times.
  6. Press the AIR/MRN button THREE times.

How do you program a Bearcat 125 scanner?

Press Hold Button and Press the channel number you want to program then hit hold again. Press “Func” (Orange Button) then hit “Pgm E” button. “Enter Frequency” will be highlighted press “Pgm E” button. Press in the frequency you would like to program, then hit “Pgm E” button when you done.

How do you program a Uniden Bearcat BC148XLT scanner?

How do I Program a Bearcat BC148XLT Scanner?

  1. Press “Manual” to stop the scanning process. Press the number for the channel you want to program using the keypad on the scanner base.
  2. Enter the frequency, including the decimals, using the buttons on the keypad.
  3. Press “E” to store the frequency. references.

How do I reset my Uniden Bearcat BC350A?

Press and hold the L/O and PROG buttons. While holding L/O and PROG, turn the scanner on. Release the L/O and PROG buttons. The scanner has been reset to factory-new status.

How do you program a scanner?

Put the scanner in manual programming mode.

  1. After you hit “Manual,” enter the channel number you wish to use, followed by “Manual” again.
  2. Alternately, if you do not have a list of frequencies or just want to explore a bit, you can hit the “SCAN” button and the scanner will scan available frequencies.

How do I reset my Uniden?

A: We suggest the following handset reset procedure.

  1. Disconnect the Battery.
  2. Press and Hold the Star and Pound key.
  3. Reconnect the battery while holding down both keys.
  4. Wait for the long beep.
  5. De-register and Re-register the handset, if this doesn’t resolve the issue.
  6. Clear the memory of the handset.

How do I reset my Uniden Bearcat scanner Bc355c?

Bc355c reset To reset scanner, press and hold “L/O” and “PROG” while turning radio on. Screen will say “clear”. Let go of buttons. There you go!

What does close call mean on scanner?

Close Call® RF Capture Your scanner’s Close Call feature lets you set the scanner to detect then display the frequency of a nearby strong radio transmission such as mobile and handheld two-way radios in areas with no other strong transmission sources.

How do I scan with the bc350a?

To start scanning, press any bank key. When the BC350A is scanning, you can see the “SCAN” message mov- ing across the display. Scanning stops on any active channel automat- ically and displays its frequency, except those channels programmed with L/O (Lock Out).

What does bc350a mean?

The BC350A comes with five Service banks for monitoring police, fire/emergency, marine, air, and weather frequencies. Not only that, there’s even a fully programmable bank for storing your own private col- lection of favorite frequencies. With the BC350A, you can scan almost 1,000 channels.

Does the bc350a have memory back-up?

A Word About Memory Back-up Your BC350A has a convenient type of memory back-up system. In the event of a power failure, the scanner provides approximately 30 days of memory retention so you don’t immediately lose the frequencies you stored in any of the channels.

How do I program lock the bc350a?

The BC350A has a program lock feature [Memory Lock] to prevent acci- dental programming entries or unauthorized programming. Simply turn on the MEMO LOCK switch on the rear panel to disable [PROG] and pro- tect the memory.